\u00a9 2021 wikiHow, Inc. All rights reserved. Others lay on top of the bars and wrap around them with straps. Hitch-Mounted Bike Racks. When using wedge anchors to install bike racks, it is recommended tamper-proof nuts be used. This image is not<\/b> licensed under the Creative Commons license applied to text content and some other images posted to the wikiHow website. This eliminates the need for the rack to be mounted to the surface. This image is not<\/b> licensed under the Creative Commons license applied to text content and some other images posted to the wikiHow website. For example, if your bikes vary between 100-150mm or 4 -6 inches in length you can mount them all at the same height, so that they’ll look neater on the wall. This image is not<\/b> licensed under the Creative Commons license applied to text content and some other images posted to the wikiHow website. wikiHow's Content Management Team carefully monitors the work from our editorial staff to ensure that each article is backed by trusted research and meets our high quality standards. Always make sure to wear appropriate safety equipment and following any safety instructions from manufacturer when installing anchors. 7. With asphalt surfaces, like an existing parking lot, you do not want to install directly into the asphalt. Hammer wedge anchor into hole deep enough so that threads are below surface of base material. Hammer spike anchor into hole deep enough where flange is flush to the surface. wikiHow, Inc. is the copyright holder of this image under U.S. and international copyright laws. With this, bike racks are mounted to a metal c-channel or rails. Mark locations of holes by marking through the mounting holes in the flange. You should still check the manufacturer’s website even if you measured the cross bars for a roof-mounted rack. This anchor is nearly impossible to remove. If a bike rack is able to be removed from the surface it is mounted to, it becomes useless as the bike lock can simply be slid off the rack and now the bicycle can easily be stolen. The best way to install a bike rack with a surface of pavers is to remove the pavers where the legs of the bike rack are to be installed. You just need to know about the rack’s set up and what type of bike you’ll be fitting on it. wikiHow, Inc. is the copyright holder of this image under U.S. and international copyright laws. Trace the cable coming out of the left brake lever to the caliper near the front wheel. Most trunk-mounted racks do not have a complicated assembly and come in one piece. Pros: Bike racks can be removed and the surface will remain flat, Cons: Bolts are only tamper proof and could be removed by thieves to remove the bike rack, Jump to: Drop-in Anchor Installation Instructions. If you don’t know which side of your rack is the front, look for adjustable poles that stick out of one end. A-Frame Mounted Racks. Or a 5/8” drill bit for a 3/8” anchor. Place washer on anchors, then nuts. 5. I built this rack so that the rear wheel from one of our bikes could rest on the floor. The best way to install a bike rack with a surface of pavers is to remove the pavers where the legs of the bike rack are to be installed. Whether you need a Honda CRV bike rack or a bike rack for Jeep Liberty, these manufacturers design a bike rack that fits your specific vehicle and is easy to use. Place nut on wedge anchor to protect threads during installation. Please refer to the documentation that accompanies your product or local codes for specific installation instructions. A bike’s weight fights against the tension of the trunk and if you add too many bikes, the mount could break. It should rest pretty easily in the grooves of your rack. This image is not<\/b> licensed under the Creative Commons license applied to text content and some other images posted to the wikiHow website. For more natural surfaces - like dirt, grass, crushed limestone - pouring concrete footings for an in-ground installation is the best decision. Pros: Bike racks can be removed without damaging concrete, Cons: Could be tampered with to make bike racks unsecure; When bike racks are removed, the bolt will remain protruding from the surface causing unsafe conditions, Jump to: Wedge Anchor Installation Instructions. This type of anchor is most advantageous if the bike rack will be removed permanently or for a longer duration of time - like during a winter season. A standard nut on a wedge anchor can easily be removed by thieves with common hand tools. You can install multiple roof racks though if you want to store 2-4 bikes. If biking is your sport, you’ve got several options for hauling one or more bikes. The anchor can also be expanded using a Hollow-Set Tool. Please consider supporting our work with a contribution to wikiHow. Most racks have safety straps to use as support, so attach these to your SUV to prevent bouncing and scraping. The concrete surrounding the anchor will need to be chipped away to remove and uninstall the bike rack. Once your bike is mounted on top of the rack, simply lift the bar up until it is resting against the frame and then secure it with the strap or hook at the end. This image may not be used by other entities without the express written consent of wikiHow, Inc.
\n<\/p>

\n<\/p><\/div>"}, {"smallUrl":"https:\/\/www.wikihow.com\/images\/thumb\/b\/b5\/Put-a-Bike-Rack-on-a-Car-Step-7.jpg\/v4-460px-Put-a-Bike-Rack-on-a-Car-Step-7.jpg","bigUrl":"\/images\/thumb\/b\/b5\/Put-a-Bike-Rack-on-a-Car-Step-7.jpg\/aid11238013-v4-728px-Put-a-Bike-Rack-on-a-Car-Step-7.jpg","smallWidth":460,"smallHeight":345,"bigWidth":728,"bigHeight":546,"licensing":"